What is a Cone Clutch?
A cone clutch serves the same purpose as a disk or plate clutch. However, instead of mating two spinning disks, the cone clutch uses two conical surfaces to transmit torque by friction.
The cone clutch transfers a higher torque than plate or disk clutches of the same size due to the wedging action and increased surface area.
Cone clutches are generally now only used in low peripheral speed applications, although they were once common in automobiles and other internal combustion engine transmissions.
They are usually now confined to very specialist transmissions used in racing, rallying, or in extreme off-road vehicles, although they are common in powerboats, dredge pumps, and other ship-drive lines.
This is because the clutch does not have to be pushed in all the way and the gears will be changed quickly. Small cone clutches are used in synchronizer mechanisms in manual transmissions and some limited-slip differentials.
Parts of Cone Clutch
- Cones: female cone (green), male cone (blue)
- Shaft: the male cone is sliding on the splines.
- Friction material: usually on a female cone, here on a male cone.
- Spring: Bring the male cone back after using the clutch control.
- Clutch control: separating both cones by pressing.
#1. Cone.
In cone clutch there is two types of cone, female cone (green), male cone (blue)
- Female Cone. It is the part of a cone that is connected to the flywheel of the engine and also rotates with it. This cone has an inner cutting cone-shaped groove through which the outer cone meshes and thus comes into frictional contact in order to engage the drive.
- Male Cone. It is the part of a cone clutch that is connected to the transmission shaft and is machined in the shape of a solid cone, over which friction material is attached. When the clutch pedal is released, the outer cone comes into contact with the inner cone due to the spring action of the released spring behind it and the drive takes place.
#2. Shafts.
The inner cone, which is attached directly to the flywheel, is mounted over a solid shaft. The outer cone, however, is mounted over the spline shaft.
#3. Springs.
Behind the outer cone, there are springs that serve to keep the inner cone in engagement with the outer cone.
When the clutch pedal is disengaged, the spring is compressed and the inner cone separates from the outer cone, thus disconnect the driving shaft from the driven shaft.
#4. Sleeves.
Sleeves are the part of the clutch which is attached to the male cone and mounted on the splines and these sleeves are used for the motion of the male cone.
#5. Pedal.
A clutch pedal is used to operate the clutch. When the clutch pedal is pressed, the spring is compressed through the fulcrum attached at its other end.
#6. Flywheel.
It is the part of the engine used to store the engine output it can be considered the part of a clutch system as the female cone of the cone clutch is attached to the flywheel and rotates with it.
How does it Work?
The male cone is engaged with the female cone due to the pressure of the spring provided behind the male cone.
When the clutch pedal is pressed to change gears or for any other reason, the pivot point attached to the pedal rotates, which in turn compresses the spring and also pulls the male cone away from the female cone.
This breaks the contact between the male cone and the female cone. Thus, the engine shaft is separated from the gear system and the rotation of the engine shaft or driveshaft is not transmitted to the gear shaft or the driven shaft.
After disengagement, when the clutch pedal is slowly released by the driver after the gear change, the fulcrum attached to the pedal rotates and the spring expands and the male cone begins to move towards the female cone over splines.
The male clutch then comes into contact with the female clutch and frictional forces act between the inner friction lining of the outer cone and the outer friction lining of the inner cone.
The cone clutch should now be in the engaged position and the rotation of the engine shaft or drive shaft is transmitted to the gear shaft or driven shaft and both shafts begin to rotate at the same speed.
The stiffness of the spring holds the outer cone and the inner cone of the cone clutch in the engagement position.
Advantages of Cone Clutch
- It creates less noise than plate clutch.
- Less wear and tear as compared to displacement clutch.
- A small axial force is required to keep the clutch engaged.
- Simple design.
- Higher torque can be transferred than the same size of plate clutch due to large amount of frictional force involved.
Disadvantages of Cone Clutch
- A high level of maintenance is required, as very little wear can cause a significant part of the axial movement of the inner cone.
- Disengaging becomes very difficult if the cone angle is smaller than required. The cone angle should be exactly as desired for easy disengagement.
Applications of Cone Clutch
- Cone clutch is used in low peripheral speed applications.
- Cone clutch is common in automobiles and other combustion engine transmissions.
- It is also used in very specialist transmissions in racing, rallying, or in extreme off-road vehicles.
- Cone clutches are used in power boats.
- Small cone clutches are used in synchronizer mechanisms in manual transmissions.
FAQs.
What is a cone clutch?
A cone clutch is a type of mechanical device used in various automotive and industrial applications to transmit torque. It consists of two conical surfaces, one fixed and one movable, which engage when pressed together.
Why is cone clutch obsolete?
They consist of two conical surfaces, one on the driving shaft and the other on the driven shaft, which come into contact to transfer the torque. However, cone clutches have become obsolete due to several reasons, including small cone angles, exposure to dirt and dust, and difficulty in disengaging.
What are the disadvantages of a cone clutch?
The main disadvantage of the Cone clutch is If the angle of the cone is made smaller than 200 the male cone tends to adhere to the female cone and it becomes difficult to disengage the clutch.
Why are cone clutches better than disc clutches?
The cone clutch transfers a higher torque than plate or disk clutches of the same size due to the wedging action and increased surface area. Cone clutches are generally now only used in low-peripheral-speed applications, although they were once common in automobiles and other internal combustion engine transmissions.